AVProedge
Non-48kHz HDMI Source with AC-MXNET-1G-DANTE-EV2
Not just a resolution, an innovative solution. MXNet's advanced hardware design allows a Dante encoder to act as more than just a standard HDMI-to-Dante on-ramp. Connecting the balanced analog output to the analog TRS input allows an integrator to ...
MXNET EV/DV2 FPGA Firmware Mismatch - How to Check & Resolve
MXNET Firmware Update: Troubleshooting Guide Issue Overview: AVPro Edge’s latest FPGA firmware update (version 9.18.9) introduces valuable enhancements, but some users with older firmware (version 9.13.1) may experience compatibility issues, ...
How To: Using the MXNet USB Control Tool
Powerpoint and software for the USB Control Tool used when configuring Point To Point, Multicast Settings, and Control Routing. Extra information. To manually set the channel to 0000 via command line astparam s ch_select 0000;astparam save;sleep ...
Where do I get MyUart
The MyUart software is available here. You may need to also load the USB driver which is also attached. https://support.avproedge.com/portal/en/kb/articles/uart-rs232-serial-communicator
How to improve switching times when you have mixed HDCP sources
If you have some none HDCP sources and some HDCP sources or even sources that are mixed between 1.4 and 2.2 then switching between sources can be slow as the display takes a while to renegotiate the HDMI handshake and switch between the various ...
How copy an EDID from an output using API commands on Axion and HDBT matrices and apply to an input
You can read the EDID from an output you want with the following command on the console page: GET OUTx HP EDID DATA : Get HDMI Output x EDID DATA{x=[1~4]} GET OUTx TP EDID DATA : Get HDBT Output x EDID DATA{x=[1~4]} Then you can load any EDID block ...
How to cycle the power on a POE port on an MXNet switch to reboot an encoder or decoder or CBOX
To do this you need access to the Web GUI of the MXNet POE switch. The 24 and 48 port switch have a management port. First you must set the management port of the MXNet POE switch to a valid IP address for your network. You can view the KB article ...
How do I setup audio return paths in MXNet 1G V2
A decoder can only be routed to one encoder at a time. You can't have one decoder sending an Audio Return Signal to multiple encoders, for example. A lot of sites utilize CEC for volume adjustment/control of source and sink devices, this ...
IR within AVProEdge solutions
We often are asked about the specification and setup of IR within AVProEdge solutions The IR output voltage for AVPro products is standardized at 5 volts - so IR emitters that are connected should be 5V IR Receivers (an IR Eye) should also be 5V as ...
How to set up an Araknis 310 Switch to use with AVProEdge MXNet
We always recommend using the AVProEdge switch range when installing an MXNet system. These switches are very high end and come with a 10 year warranty and are pre configured out of the box to work with MXNet. However, if budget is a concern and you ...
How do I get SkyQ on 10 Bit Colour with MXNet and be able to watch HDR content?
SkyQ needs to have an EDID that it likes to allow you to select 2160p 10 Bit. If it does not have an EDID it is happy with it will not allow you to select 10 Bit colour and it will not offer the option to download UHD HDR content and will not play ...
How to setup MXNet switches to be accessible on the LAN and via Switch Management on Mentor
The MXNet switch has an RJ45 port labelled Mgmt which is the management port. You can access the management port by connecting a patch lead to the management port and connecting the other end to your computer. By default the IP address of the ...